Bushtech Aluminium Canopy for Ford Ranger T6 2nd Gen (2023-current)
Gullwing aluminium canopy, built in Africa
R 43,125.00incl VAT
Loading
Every Bushtech product available in South Africa that fits the Ford Ranger: T6 2nd Gen 2023-current · T6 1st Gen 2012-2022. Prices include 15% VAT.
Gullwing aluminium canopy, built in Africa
Gullwing aluminium canopy, built in Africa
The working spec canopy, raw aluminium doors
The working spec canopy, raw aluminium doors
The fleet canopy, raw aluminium throughout
The fleet canopy, raw aluminium throughout
Carpeted, shelved, cut for the Next-Gen Ranger load bin
Showing 16 of 72
Gullwing aluminium canopy on custom extrusions, with a roof tested to 2,500 kg under static load. Both sides and the rear open at once, sealed by continuous dustproof hinges and automotive grade door seals. The subframe takes the full accessory range.
Every canopy is built to the exact body lines of your generation and cab. Fitting takes about two hours and nothing is drilled.
A few things decide the fit. Answer here, or open a row for the picture. We ask again when you order, and those answers go on your fit confirmation.
A factory styling bar or roller cover comes off before the canopy goes on.
The side plastic trims come off for the fitting; the rear tailgate trim stays on.
Allow three to four hours for the fitting: the factory tie-down points are thread-locked and take time to remove.
Photographs: Kevauto, Wikimedia Commons (CC BY-SA 4.0), Alexander-93, Wikimedia Commons (CC BY-SA 4.0), ArmorThane, Wikimedia Commons.
Download the fitment notes for the Ford Ranger T6 2nd Gen (PDF, with photographs)
Light enough to carry more. The 2,500 kg figure is a static test: the load sits still on the structure while it is measured. The packed weight is the factory’s own, with the carton, from September 2026.
Photographed on the current Ranger at the factory in Johannesburg. Load bin and payload intact: the canopy clamps on, and comes off again for resale.
Nothing on this canopy is a dead end. The subframe already carries the mounting for every drawer, cupboard, table and ammo box we build, so each one clips in with no drilling and no bracket kit. Buy the canopy once, add to it for years.
Filtered to your bakkie
The Ranger T6 2nd Gen (2023-current) and Ranger T6 1st Gen (2012-2022), in the cab styles each generation supports. You choose the generation and the cab on the product page.
No. The canopy clamps to the load bin and comes off clean. Nothing is drilled and the load bin liner stays where it is.
Yes, with two people and roughly half an hour. We would rather you did not do it alone: a double cab canopy is 70 kg and it is awkward before it is heavy.
A double cab canopy weighs 70 kg, so the payload stays with the fitout. Packed for shipping with its carton it is 83 kg, measured at the factory in September 2026.
Toyota Hilux Revo[70]
Ford Ranger T6 2nd Gen[64]
Isuzu D-Max RG Facelift[58]
Toyota Land Cruiser 79 Series[82]Toyota Hilux N90 Travo[64]Ford Ranger T6 1st Gen[62]Toyota Hilux Vigo[63]
Isuzu D-Max RG 7th Gen[59]Mazda BT-50[46]
Isuzu D-Max RT50 6th Gen[50]Mazda BT-50[47]
Ineos Grenadier Quartermaster[46]Nissan Navara D23 Facelift[48]
Jeep Gladiator[46]Nissan Navara D23[48]Nissan Navara D40[48]Nissan NP300[47]Nissan Patrol pickup[48]Volkswagen Amarok 2nd Gen[48]Volkswagen Amarok 1st Gen[48]GWM P-Series[48]Land Rover Defender 130[47]JAC T9[46]Foton Tunland G7[46]Mahindra Pik Up[46]Peugeot Landtrek[47]
